Tag Archives: How To

How to Clean Smoke Damage from Wood

How do you clean smoke damage from wood? What you should do is gently clean the wood with a soft cloth and then vacuum the wood to pick up the soot. When it comes to soot removal, every wood requires a specific procedure. However, it’s possible that the damage goes beyond the surface. The more you let the smoke linger, the more it soaks into the wood; therefore, cleaning the wood should be done sooner rather than later. Prior to starting the cleanup process, you should determine whether the wood is finished or unfinished. This article will present a quick guide on how to clean smoke damage from wood.

How to Clean Smoke Damage from WoodHow to Clean Smoke Damage from Wood

Cleaning Soot from Finished Wood

A finished wood is covered by a protective coating to give it a polished look. It should be cleaned with duster or a high-efficiency particulate air (HEPA) vacuum. The two will pick dry soot before you start cleaning deeper into the wood. There are special vacuums made to do the trick. After that, clean the area with a dry chemical sponge until the surface turns black.

For best results, make sure the sponge is dry. Pay attention to the pressure you apply on the sponge as it can permanently embed on the smoke residue. If the wood is affected by smoke, run your hand over the wood surface. To clean the soot, rub the surface with cotton rags or oil soap. But if more agitation is needed, you can use steel wool and work in the direction of the grain. This will preserve the finish of the wood.

If the oily soot still remains on the wood, dilute a degreaser in a bowl and spread on the surface of the wood. After that, rinse with a wet cloth and dry with a soft towel. You may also want to rub a bit of polish on the wood, this will help you get rid of the unattractive marks.

Cleaning Soot from Unfinished Wood

Unfinished wood comes with a different level of roughness. The soot residue will embed into the wood a few minutes after the fire. You should use an odor-removing spray specifically created to deodorize the pervasive smell of smoke on the wood surface. Secondly, remove the soot with a vacuum hose.

For deep cleaning, run a HEPA vacuum over the sooty surfaces. This will help you pick as much soot as possible. Thirdly, use a chemical sponge across the wood surface. When one side of the sponge turns black, turn to the other one.

To expose the new layer of the wood, cut the blackened parts. Additionally, dilute some degreaser with water and then spray evenly on the surface of the wood. Since unfinished wood is easily stained by smoke than the finished one, you should sand away any remaining stains. You can also use fine grit sandpaper to work on the heavy stains. In no time, your unfinished piece will be as good as new. Make sure you seal the unfinished piece.

Final Thoughts

How do you clean smoke damage from wood? Use a soft cloth and a HEPA vacuum to clean finished wood or an odor-removing spray to clean unfinished wood. While you can’t salvage everything in your house after a fire, you can clean your smoke-damaged wood. By following the above guide, you’ll return wood to a like-new condition. It’s important that you clean up the surface immediately to reverse the effects of the damage.

How to Fix Laminate Floor Water Damage

Laminate flooring is increasingly gaining popularity among homeowners due to its appealing look, functionality and durability. By design, laminate flooring will last for years with minimal effort. Laminate flooring and water, however, have a complicated relationship. The wood materials in laminate floors are susceptible to water damage. So, how do you fix laminate floors with water damage? Laminate is designed to withstand occasional spills if installed in accordance with manufacturer instructions. Direct water damage caused by improper or unprofessional installations is a different matter that can lead to unexpected expenses. When laminate becomes supersaturated with water, it starts to absorb the moisture which breaks down the composition of the laminate material. In the long-run, the plumbing leaks, wet mopping and liquid spills lead to a whole host of problems. If left unattended, you will notice that some planks begin to get buckled or bent in awkward ways. All these are signs that your laminate flooring need to be fixed and some tips on how to fix laminate floor water damage.

Signs of Laminate Floor Damage:

To know whether your laminate floor is damaged, look out for the following symptoms:

  • Bubbling.
  • Splitting.
  • Buckling.
  • Cracking.
  • Excessive cupping.
  • Visible mold.
  • Discoloration and much more.

The sad news is that majority of the above-listed symptoms cannot be rectified. Lucky for you, these floor mishaps caused by water damage can be fixed by following simple steps for replacing discussed below. Depending on the size and situation of the damage, you may need to replace the entire room. If the damage is severe, you can hire a professional to get the job done.

How to Fix Laminate Floor Water Damage

How to Fix Laminate Floor Water Damage?

  1. Be Sure That the Source of Water Damage Is Contained

There is no point in fixing your laminate floor if it is just going to be damaged again. Find the source of the flooding or leaking and take care of it. By putting your laminate floor repair job on hold till you are sure that the flooding or leaking has ended, you will protect your floor from being waterlogged in future.

  1. Inspect the Locking System to Identify Damaged Plans

By doing this, you will determine the destroyed areas. This step should be easy, but it will require your undivided attention. Check for warping and bubbles, also be thorough in your evaluation. Mark the affected areas with a marker pen or sticky notes according to the severity of the damage. This way, you can quickly access how far-reaching the damage is and take the appropriate measures.

  1. Get the Right Tools for the Project

Here’s a checklist of the things you will need to get the job done: safety glasses, flooring adhesive, putty knife, utility knife, measuring tape, cleaning solvent, pliers, hammer and replacement underlayment material. You will also need to find a new laminate planks that match your existing flooring. It is not easy to find matching laminates and many homeowners opt to replace the entire floor instead of just fixing the damaged portion. Avoid last-minute shopping trips to the flooring store by having the mentioned materials ready ahead of time.

How to Fix Laminate Floor Water Damage

  1. Remove the Laminate Up to the Problem Zone

You will need to use the right tools for this task. If you don’t want to spend money on purchasing new equipment, you can hire a professional. Before you settle on a technician or flooring company, do a background check to ascertain their credibility. If you choose to do it yourself, carefully pull up the damaged planks by running a putty knife under the damaged edges. You must get rid of the entire plank even if only a small portion of it is damaged. This is because every plank is a single unit. Pry up the planks as well as the baseboard to expose the bare floor beneath. Check the sub-flooring for any sign of mold or mildew. If you don’t notice any damage, reinstall the planks that are popped up.

  1. Replace the Damaged Planks.

Replacing the damaged planks might be the biggest challenge. Ensure to replace using the

same laminate planks you have installed. Unless you bought extra planks when you first installed them, getting exact replacements can be daunting as you could soon discover. To avoid replacing the whole floor, purchase from the same manufacturer or laminate flooring dealer, or at least find a suitable replacement that will balance nicely. Get rid of moldings in preparation for replacing flooring.

  1. Finish by Reinstalling The Flooring.

Remember to match any designs on the laminate flooring as closely as possible. Apply enough adhesive and place and heavy object on your new laminate. If installing in water prone areas, like the bathroom, allow the floor to dry completely before using.

How to Fix Laminate Floor Water Damage

Conclusion

Fixing water damaged laminate floors is not an easy task, but by using the above-discussed tips on How to fix laminate floor water damage? you will be able to repair your laminate floor without having to install a whole new floor. Titan Restoration of AZ, is an amazing company that can be of emergency assistance, 24/7, if you are unsure of exactly how to handle the task or need an experts suggestion.